repairlop.blogg.se - 2012 nissan versa mass air flow sensor problems

#2012 NISSAN VERSA MASS AIR FLOW SENSOR PROBLEMS HOW TO#
#2012 NISSAN VERSA MASS AIR FLOW SENSOR PROBLEMS DRIVER#
#2012 NISSAN VERSA MASS AIR FLOW SENSOR PROBLEMS FULL#

NHTSA ID: 10044780 TSB ID: NTB-12-051 Nissan: with regards to certain model vehicles, no drivability concerns when mil is on for mass air flow sensor (maf) stored in ecm. NHTSA ID: 10046601 TSB ID: NTB-10-102-A Nissan: bulletin regarding diagnosis of abs/vdc wheel speed sensor. if there is a leak in the brake master cylinder is identified the brake master cylinder resevoir will be topped off if no leak is present. brake system will be inspected to confirm that no brake fluid leak is present. NHTSA ID: 10051828 TSB ID: NTB12-011C Brake master cylinder.

#2012 NISSAN VERSA MASS AIR FLOW SENSOR PROBLEMS FULL#

For the full text of TSBs: Get a 1 year subscription for only $19.95 from ALLDATAdiy! Use Code DIYDISCOUNT.

#2012 NISSAN VERSA MASS AIR FLOW SENSOR PROBLEMS DRIVER#

NHTSA ID: 10052407 TSB ID: NTB-13-007 Nissan: service information on the removal and installation of service parts, on certain vehicles, for the steering wheel switch, if needed, without replacing the driver airbag module. NHTSA ID: 10053958 TSB ID: NTB-13-097 Nissan: certain vehicles would display, in the instrument cluster, a warning light illumination of a loose fuel cap warning. NHTSA ID: 10074565 TSB ID: AT13-014D Summary to be provided on a future date. important: make sure this incident has been duplicated at a gas station by dealer NHTSA ID: 10109214 TSB ID: NTB17-030 Nissan fuel tank is slow or difficult to fill if you confirm the fuel tank is slow or difficult to fill (filling nozzle shuts off before tank is full). the applied vehicles and claims information sections have been revised. NHTSA ID: 10119249 TSB ID: NTB17-082a Nissan dtc p0456 caused by evap leak at vent control valve o-ring this bulletin has been amended. The hot wire sensors typically have an operating range of 0 - 5 volts.Īt full throttle, voltage is normally between 4 and 5 volts.NHTSA ID: 10119282 TSB ID: NTB16-116 Nissan diagnosis information for abs dtc c1130 service information when diagnosing for dtc c1130 (engine signal): ecm related dtcs (p-codes) must be diagnosed, repaired, and dtcs erased first. Nissan's mass airflow sensor sends a voltage to the powertrain control module (PCM).

Allow the MAF sensor to dry and reinstall.

Spray 8 to 12 spurts of MAF sensor cleaner on the exposed plate.

Remove the two screws that hold the MAF sensor secure and remove the MAF sensor.

Unplug the mass airflow sensor electrical connector.

Locate the MAF sensor next to the engine air filter housing.

Pull the hood release and open the hood.

#2012 NISSAN VERSA MASS AIR FLOW SENSOR PROBLEMS HOW TO#

How to Clean Nissan MAF SensorĬleaning the MAF sensor on a Nissan is easy and takes less than ten minutes. If your check engine light is still on, use an OBD2 scanner to clear any stored codes in the ECU.

Your ECU uses the mass airflow sensor input to determine the fuel ratio that the injectors need to deliver to the engine.

A defective Nissan Quest mass airflow sensor could make your car difficult to start.

Plug the electrical connector until it locks in place. Tighten the screws so that they are secure and tight.

Watch the following video on how to remove the air filter box to access the MAF sensor.

Unplug the electrical connector from your Nissan mass airflow sensor.

Nissan MAF sensor is located right next to the engine air filter housing, typically on the driver's side.

Locate a mass airflow sensor in the engine bay.

Your browser does not support the video tag.

Pull the hood release under the dashboard and open the hood of your Nissan.

Replacing the MAF sensor on a Nissan vehicle is very easy. Write down these codes research them to find out what each code means. Dirty, obstructed, or faulty mass airflow sensor.

Allow your scanner to turn on and communicate with the ECU.įault codes such as P0171 System Too Lean (Bank 1), P0174 System Too Lean (Bank 2), and P0101.

Turn on the ignition but do not start the engine.Plug your diagnostic scanner in this port.Locate the diagnostic port under the dashboard on the driver's side.To diagnose the Nissan MAF sensor, you will need to read the fault codes stored in the Engine Control Unit (ECU).įor this step, you will need an OBD2 scanner. How to Diagnose Nissan MAF Sensor Problems The vehicle hesitates and jerks during acceleration.The engine runs unusually lean or rich, idling.This is a list of common symptoms you will notice when your Nissan MAF sensor fails.